Welcome!

By registering with us, you'll be able to discuss, share and private message with other members of our community.

SignUp Now!

Search results

  1. willieshotg3

    ? on x1

    i was thinking of running an x1...i have a nx nitrous setup and would like to be able to pull timeing out to use more nitrous safeley...i am only running a 50hp shot now would like to go to a 100hp shot it will be progressive 50hp than add the other 50hp at a later rpm...i wanted to know can you...
  2. willieshotg3

    373 gear question

    i just put 373 gears out of a pre runner hole 3rd member into my x hav a little whine from 30-60mph just wondering if any other people with this swap have herd the same noise
  3. willieshotg3

    rear third member part #

    i was trying to find the thred that had the part # for the compleate third member with 373s. ive been serching for a whyle and cannot seem to find it. i just blew up my diff into about 35 diffrent pices all ring and pinion gear... 1/4 of th pinion gear is missing... just need the part # and i...
  4. willieshotg3

    nitrous ?

    i was wondering if any one else was running nitrous i am trying to find a 2 stage colder plug and was wondering what my optios were.
  5. willieshotg3

    whats your best n/a dyno #s

    i am running an 2006 tacoma x runner with urd cai,dt long tube headers,custom midpipe,and a custom tune that i made. i made 271hp at 5200 rpm 333 ftlb torque at 2800 rpm i am running on a mustang dyno
  6. willieshotg3

    thinking turbo

    i am thinking about running a turbo. i am wondering what size injectors to run/where to get them. and looking for a clutch. ps i am going to run 7 psi
  7. willieshotg3

    undercover pics

    here are a few pics of my undercover tonneau cover
  8. willieshotg3

    multiptle engin internal pics

    pics of a 1grfe aka a 4.0 lt in the x runner. first we got a six bolt main we got a pick of where the oil pan should be than last we have a pic of the one of the oil squirters that squirt oil on the bottom of the piston to keep it cool and lube the wrist pin. i have a 1grfe tore down...
  9. willieshotg3

    top speed

    i had no load on the dyno and the gearing tops out at 159 mph in an x runner the fastest i hit with load was 130 at the top of fith gear. truck also dynoed out at 333 ft lbs and 253 hp have a urd cai and the c2c headers with a tune
  10. willieshotg3

    turbo ?

    i was thinking about running a turbotronics t3/t4 hibred turbo at the end of my long tube header. i am wondering do you guys think it will still spool down ther or should i mod the header
  11. willieshotg3

    ? on urd maf calabrator

    i am having trubble with pulling rpm data on my laptop. i am getting the tps voltage but no rpm. all the wires are hooked up as stated in enclosed instructions. i am also using a usb to sierial adapter. just wondering if that could cause it and if so where can i get a serial port for a lap top
  12. willieshotg3

    ? on mass air flow cal

    i am having trubble with pulling rpm data on my laptop. i am getting the tps voltage but no rpm. all the wires are hooked up as stated in enclosed instructions. i am also using a usb to sierial adapter. just wondering if that could cause it and if so where can i get a serial port for a lap top
  13. willieshotg3

    wheel ?

    looking for a set of 15 inch steel wheels for the x to run slicks any one know where to get some
  14. willieshotg3

    c2c a good company

    i hope c2c is a good company i just orderd headers and have never delt with them befor. hope this will be a good experiance
  15. willieshotg3

    ? on urd mass air flow calabrater

    i was wondering do you need a scan tool to adjust the calabrater or just to see the air fule ratio to see what you need to adjust
  16. willieshotg3

    tb spacer

    just wondering who makes a tb spacer for the x and where to buy it
  17. willieshotg3

    meet

    anyone from mo want to get a meet goin i am from arround alton illinois. just let me know
  18. willieshotg3

    meet

    we need to get a meet together in within 150 miles st. louis mo... anyone interested let me know
  19. willieshotg3

    installed a computer

    i put a desktop cpu in my truck hooked it to a screen and a power inverter and poof i have a 160 gig jutebox... hope to poste pics soon
  20. willieshotg3

    anyone in stl mo area

    i am trying to get an x runner meat in stl mo area anyone interested just let me know

Forum statistics

Threads
53,684
Messages
913,735
Members
7,403
Latest member
joeypeeps22

Latest posts

Online statistics

Members online
0
Guests online
49
Total visitors
49
Totals may include hidden visitors.

Stay Connected

Top Bottom