Welcome!

By registering with us, you'll be able to discuss, share and private message with other members of our community.

SignUp Now!

Search results

  1. J

    Bullydog

    Which scanner r you using gadget? TIS?
  2. J

    Stroker kit anyone?

    Good mate, I got the general idea of ecus, lets see your dyno result then. BTW, what camshaft spec did you use for your build engine? duration, lift @.050, separation angle, centreline?
  3. J

    Stroker kit anyone?

    Hi Tor, I'd like to hear more about the proefi ecu and how it out perform X-1/UCON in real life situation. What it can do but the X1/UCON cannot. May I have some hints from you? Cheers
  4. J

    Stroker kit anyone?

    I have already got the upgraded auto trans anyways. So how does your stroker mod turn out? Are you happy with the power?
  5. J

    Stroker kit anyone?

    Wooopps....would you say a bit more about your advise? Aint you happy with your shrotered engine? I want to stick with 1GR for a reason, that as soon as the engine looks the same, I can still pass the vehicle inspection, since emission is not a problem....plus LSX swap is quite a bit more...
  6. J

    Stroker kit anyone?

    Got a complete rebuild auto trans from IPT already, need a higher stall convertor though I guess, what stall speed do you guys suggest for a strokered engine with bigger than stock camshaft and FI setup? 2600 was suggested by Dave at APR. With your upgrade have you had AT/TEMP warning light at...
  7. J

    Stroker kit anyone?

    Well the manual vehicles are not marketed here, never know that the 6spd trans is that bad. So you think my upgraded valve body will be just fine? And regarding the T56 swap, I was thinking of keeping it part time, thus I don't have to change the T-case and front diff, which will also keep cost...
  8. J

    Stroker kit anyone?

    wow...care to expand your point a bit more G? Also do you think T56 swap on a auto is possible?
  9. J

    Stroker kit anyone?

    Well, I have got auto tranny with valve body upgrade and custom made stall converter, this will do the job hopefully. I want to do the T56 swap for sure, but can I ? I guess there are too much of electronic mess to take care of if I want to do T56 on a auto FJ....sigh. BTW, I am in Hong Kong...
  10. J

    Stroker kit anyone?

    Cheers Mate, looking forward to the lengthy version from you! It will certainly be bored to at least 96mm I am not sure if I can go any further, the darton spec says 98mm maximum though. BTW I will still need your help with the EMS decision. Thanks for your reply mate!
  11. J

    Stroker kit anyone?

    Has anyone done the stroker mod? Was looking for user feedback of the kit, but failed to fine any. Anyone wants to share your experience? I am looking to do a stroked forged build with URD supercharger system, but jus want to be 100% sure I am not wasting my money on the stroker kit.
  12. J

    Installed UCON and now getting P2238 CEL code.

    Yes, similar problem as I guess, loose harness....after few days of driving the codes seems to be gone for me....
  13. J

    Installed UCON and now getting P2238 CEL code.

    Make sure you check the AFR sensor first, if you cant find any problem there, try disconnect the battery for 15 min, while the battery is disconnected tidy you harness and tie it high enough to support the weight of it, connect the battery, re-flash the cal file you want to use.... I did this...
  14. J

    Installed UCON and now getting P2238 CEL code.

    I have the same problem twice, the first time I had the code, I just replaced sensors on both banks, as they were 70000miles old anyway, but with the new sensors, I still have the same code occasionally. I start to think that might be a problem caused by UCON, (with the pre.20 release I never...
  15. J

    UCON beta test ver. 2.0

    Thanks I have the URD stage2 supercharger kit (running the injector that came with the kit), the injportsize of stage2 cal was set to 600, gadget did emailed me and suggest me to set it to 640. I did so, it did eased out the problem a little, but still the long term fuel trims are notably...
  16. J

    UCON beta test ver. 2.0

    I am testing the .20 software and stage2 cal file on my FJ as well...however I found the fuel trim to be strangely large negative numbers. OP, do you have the same situation?
  17. J

    Apr x-1 kit wanted!

    still trying hard to fined one, anyone?
  18. J

    APR x-1 help

    My dear OP,if it is the x-1 I will buy it from you any moment!
  19. J

    Apr x-1 kit wanted!

    :laugh: I m not in the us....I dissappeared since I had to sleep/work...:laugh:. I have been offered a set of TRD supercharger however there isn't Toyota official reflash service here in China, even if there is I'd probably go for X-1 anyway .
  20. J

    Apr x-1 kit wanted!

    Anyone? just let me know! I want this bad boy (including the cam gear and thermostat)!

Forum statistics

Threads
53,685
Messages
913,747
Members
7,405
Latest member
gsy971

Latest posts

Online statistics

Members online
1
Guests online
54
Total visitors
55
Totals may include hidden visitors.

Stay Connected

Top Bottom