Search results
-
2012 X-Runner pics!!!
all car makers do face lifts, then 2 years later they do a full makeover, so they can sell the rest of the inventory, so nobody holds out for new. -
Clutch Thread
I just adjusted the play in the pedel, left about inch n a half of play, truck drive so much better, none of that long wait for your foot to come back up- LD X-IN
- Post #115
- Forum: Stock Performance/Mechanical
-
poor throttle response
Mine does this after I change my oil and then slowly gos away using 10-40W. Im going to use a 0-30W next time and see if that makes a diff. These trucks r so dam senz a tiv.- LD X-IN
- Post #6
- Forum: Stock Performance/Mechanical
-
-
Engine Oil Cooler
Ok I thought oil runs to the water neck with inner tubbing to cool the oil,- LD X-IN
- Post #39
- Forum: F/I Mods & Tuning
-
Engine Oil Cooler
but the OEM plate is just a in and a out you buy hose and a radiator and you dont have to cut your oil cup ???- LD X-IN
- Post #37
- Forum: F/I Mods & Tuning
-
Engine Oil Cooler
Ya that OEM oil cooler is some big $$$ will buy the OEM sandwich plate (then look for some hose and rad. on Ebay)- LD X-IN
- Post #35
- Forum: F/I Mods & Tuning
-
Engine Oil Cooler
the OEM oil cooler, is cooled only by the antifreeze? and OEM has no little radiator??- LD X-IN
- Post #26
- Forum: F/I Mods & Tuning
-
-
Engine Oil Cooler
does that OEM part screw on ? or does it come with a longer feeder tube ? how does that work ? IDK.- LD X-IN
- Post #13
- Forum: F/I Mods & Tuning
-
Electric fan conversion (advance auto parts style)
how does x runners do w/ the E. fan, in hot parking lot traffic like on Oahu, same as stock? -
Bolts instead of studs URD Traction Bar
did your URD. studs look as bad as these, and r your new ones look better and not home made ?- LD X-IN
- Post #19
- Forum: Stabalizers & Traction Bars
-
Bolts instead of studs URD Traction Bar
bolts with a nut at the end.- LD X-IN
- Post #17
- Forum: Stabalizers & Traction Bars
-
Bolts instead of studs URD Traction Bar
Would you put this in your rear end? this was the best looking stud I had, lost the other studs over the 2 years I had the kit.- LD X-IN
- Post #15
- Forum: Stabalizers & Traction Bars
-
Bolts instead of studs URD Traction Bar
no I did drain the oil, just did not want to use the studs that came with the URD kit, and finding new studs was hard, so I used bolts instead of the URD studs, the studs from URD were cut and rethreaded, and the threads look shallow. My fear of using the URD studs were cranking them in and...- LD X-IN
- Post #14
- Forum: Stabalizers & Traction Bars
-
Bolts instead of studs URD Traction Bar
just put trac. bar on, with 3 bolts for bottom, and used a header stud for top one it was just long enuff for the nut to make a full grab on the bolt, I will post pix. of the URD studs that i did not want to use.- LD X-IN
- Post #12
- Forum: Stabalizers & Traction Bars
-
Bolts instead of studs URD Traction Bar
Ok my bolts have a 8.8 so this is to weak of a bolt for the traction bar or are they good ? Thanks- LD X-IN
- Post #9
- Forum: Stabalizers & Traction Bars
-
Bolts instead of studs URD Traction Bar
Its been 2 yrs since I had it on my truck since then lost 2 studs and no stores here sell studs that are that long they said cut the bolt head off, thats another way, but are Grade 8 bolts strong enough? Changing Grades I heard is a no no Thankz- LD X-IN
- Post #7
- Forum: Stabalizers & Traction Bars
-
Bolts instead of studs URD Traction Bar
I was running the URD studs, the threads are so shallow . I took them out in fear they would mess up the threads on the rearend, Im going with the bolts, but the thing Im wondering is, are those studs a Grade 10? because they have a black hardin finish to them or is that just paint, My Grade 8...- LD X-IN
- Post #5
- Forum: Stabalizers & Traction Bars
