Search results

  1. Ziggy297

    Xii performance and street taco

    From who? Street Tacos or XII? The folks at XII performance were hit pretty hard with the hurricane and flooding, Amy had posted several pictures on Facebook with what they were dealing with. If it is them who you requested a refund from I would try to be a little understanding, what happened to...
  2. Ziggy297

    AC harness issue

    I just bought the connector off ebay ( had to get the entire harness) for $120 and bought the new resistor, and climate control panel. The blower speed switch was toasted bad when I took it apart. That copper got pretty damn hot to do the damage it did.
  3. Ziggy297

    AC harness issue

    I recently lost all but 1 speed ( medium) on my AC in my 2010 X. I went online and the problem everyone else has had was the blower resistor but their blower was on high only. I pulled the AC module out and found a charred wire connection ( pics attached). Has anyone else had this issue? I am...
  4. Ziggy297

    Sway Bar and Trac Bar Installation Instructions

    What I have is the coilover and leaf spring install instructions, couldn't find the sway bar instructions.
  5. Ziggy297

    Sway Bar and Trac Bar Installation Instructions

    I believe I still have the instructions at home, I can check tonight when I believe I still have the instructions and parts list, I can check tonight when I get home.
  6. Ziggy297

    2010 Build - after 8 years

    The BBK is a must! Did you happen to pass through Oakley on your maiden drive home? I saw. SWB X around that time on highway 4 and gave the driver a thumbs up.
  7. Ziggy297

    Xii performance and street taco

    My advice to you is continue to try to call Streetacos. You may be waiting a very long time.
  8. Ziggy297

    Xii performance and street taco

    XII Performance will get back to you for sure. They are really great people and won't leave you hanging, they may just be tied up. I ordered my entire suspension through them without any issues. Streetacos sucks, took 9 months for a set of lowering blocks. Great quality but the dude lags, I...
  9. Ziggy297

    OEM Shift Knob, 2010

    It's on it's way Cal Frez!
  10. Ziggy297

    performance brakes unlimited

    I will keep you posted!
  11. Ziggy297

    performance brakes unlimited

    No worries I'm not taking it as a flame war/argument at all bud. The Tacoma MC is 13/16" and the Tundra is 15/16". The difference in the booster is the Tacoma is a single diaphragm and the Tundra is Dual diaphragm. I read on other forums some folks used a GM MC but the rod had to be cut and...
  12. Ziggy297

    performance brakes unlimited

    Yes it is, you need a separate reservoir when you do the mod. I bought the Ring Brothers reservoir but there are cheaper options. I haven't installed any of it yet so I can't tell you how much better it is or isn't. The reason I am going this route is because I am installing 6 piston fronts and...
  13. Ziggy297

    performance brakes unlimited

    You use the Tundra master cylinder as well which is a bit larger than the Tacomas.
  14. Ziggy297

    performance brakes unlimited

    Yes they are, I just bought the Tundra Master cylinder and brake booster conversion from them.
  15. Ziggy297

    OEM Shift Knob, 2010

    Just give me your address and I will send them to you.
  16. Ziggy297

    URD stage 3 clutch disc

    Thanks Torspd! This was a fun project even though it took so long with the time constraints. After the powder coating I will post the final picture.
  17. Ziggy297

    OEM Shift Knob, 2010

    P PM me your address and I will send it to you. Just pay It forward to someone else. They aren't doing me any good here and will end up getting thrown out after a while anyway. I should have mentioned they are almost new, a touch of wear on the knob. I will edit with pictures when I get home.
  18. Ziggy297

    OEM Shift Knob, 2010

    I just did a T56 swap and have both as well out of my 2010 if you are still looking.
  19. Ziggy297

    URD stage 3 clutch disc

    In and mounted, after a week I will pull it out and have it powder coated. Working on a longer shift stick now to give me a few more inches.
  20. Ziggy297

    URD stage 3 clutch disc

    Welded the cup holders in, a little high on the heat so I have a bit of repair work to do. I started to machine the hold down clips, 3 down 3 more to go.
Top