whats your best n/a dyno #s

[willieshotg3]

i am running an 2006 tacoma x runner with urd cai,dt long tube headers,custom midpipe,and a custom tune that i made.

i made
271hp at 5200 rpm
333 ftlb torque at 2800 rpm

i am running on a mustang dyno

 

[VIPDreamin]

211.9 bone stock with an untuned MAf and A?F at a lovely 10 after 4500k. Not bad for 65k miles...Im pretty sure my next dyno will show a small improvement:biggrin:

This was ona dynojet

 

[jaxchrisfla]

i am running an 2006 tacoma x runner with urd cai,dt long tube headers,custom midpipe,and a custom tune that i made.

i made
271hp at 5200 rpm
333 ftlb torque at 2800 rpm

i am running on a mustang dyno

wheres the graph? That a hell of a lot of torque, let alone power for those mods. Those are base numbers on a trd s/c.

 

[Stevenredx]

wheres the graph? That a hell of a lot of torque, let alone power for those mods. Those are base numbers on a trd s/c.

Don't the mustang dyno's give higher readings anyway :dontknow:

 

[skilledbum23]

Don't the mustang dyno's give higher readings anyway :dontknow:

what he said:dito:

 

[VIPDreamin]

Don't the mustang dyno's give higher readings anyway :dontknow:

Yes they do depending on the load setting.....

 

[Simplex Effect]

Thats pretty impressive #'s even though the dyno reads higher than most.

 

[wshsbears]

can't be too far off.. thats about the same mods rexrunner has and only 10 more hp.. i think the tq is close too..

 

[Gadget]

Here is the best my truck did N/A.

URD TCAI, URD Y-Pipe, URD Cat-Back, and URD MAF Sensor Calibrator, stock manifold with stock cats.

 

[Gadget]

Don't the mustang dyno's give higher readings anyway :dontknow:

Man, those Mustang dynos sure are mysterious.

One day people claim they read low, the next they claim they read high.

Gadget

 

[Yotaman]

i am running an 2006 tacoma x runner with urd cai,dt long tube headers,custom midpipe,and a custom tune that i made.

i made
271hp at 5200 rpm
333 ftlb torque at 2800 rpm

i am running on a mustang dyno

Those are really good numbers! :top:

Hope to get mine Dyno'd after I get the MAF!

 

[Yardie]

Man, those Mustang dynos sure are mysterious.

One day people claim they read low, the next they claim they read high.

Gadget

:laugh: I thought the same thing. I've always known them to read lower :dontknow:. You might want to check your AFR from that custom tune. You might be running really lean to make that much power. My stock NA dyno was 199hp.

 

[jaxchrisfla]

im making 244hp, and 266 tq, with urd intake and maf cal, long tubes, and custom exhaust. The maf cal was tuned on the dyno after all mods installed.

 

[Xacto]

269 rwhp 292 rwtq. 333 rwtq? lol those are s/c torque numbers

 

[VaBchXRunner]

225 HP/275 TQ N/A
Now S/C 315 HP/ 325 TQ:top:

 

[overdriven]

Man, those Mustang dynos sure are mysterious.

One day people claim they read low, the next they claim they read high.

Gadget

:dito:Was thinkin the same thing.
I'd hate to discredit the guy, but 333rwtq NA, especially at 2800rpm sounds like something is off with the dyno and the load settings. Looking at other graphs torque is peaking around 4000.

 

[jaxchrisfla]

:dito:Was thinkin the same thing.
I'd hate to discredit the guy, but 333rwtq NA, especially at 2800rpm sounds like something is off with the dyno and the load settings. Looking at other graphs torque is peaking around 4000.

my peak is about 3800.

current setup. after tune is the higher numbers.

with urd intake, maf cal untuned, and longtubes.

 

[07SWB]

you guys are lucky... i have K&N CAI, DT LTs, Stocky y-pipe, and a magnaflow 18" muffler, MAF calib (factory tune) and the o2 sim, and i only put down 229rwhp and 273ftlbs

 

[jaxchrisfla]

if you look at the second graph compared to the first, you see how much torque you loose on the low end when you open up the exhaust alot on a n/a motor. running no cats and larger piping will kill low end. I still have the factory y pipe, but its cut and ran true dual into a single out muffler. i lost ~25tq at 2.5k rpms.

 

[Dallas]

something aint right with that mustang dyno, I had my x with only the TRD blower and it was 275 hp 299 ftlbs. on a cool day