o0opackersfano0o
Active Member
- Joined
- Jun 23, 2016
- Messages
- 443
- Reaction score
- 100
https://www.tacomaworld.com/threads/xrunner-build.642035/
2005 Toyota Tacoma xrunner
Bc rods
Cp ceramic coated pistons 9.5-1 compression
Arp head studs
All new Toyota bearings
Kelford custom cams with valve springs
New water pump
New timing chain with tensioner
Motor has less the 10k on rebuild
Tons of parts powder coated while motor was apart. No leaks nothing wrong with motor
Small port and polishing job on heads and intake along with super charger
76mm throttle body
Magnusson supercharger. Been on for around 15k
2.3” pulley making around 12 psi
Nst pulleys. Crank, supercharger lower, water pump, alternator
Super charger over flow tank in bed
Trd upgraded intake from 4 runner with new maf sensor
Doug thorley headers
Urd y pipe
Urd 3” cat back
Urd 170 degrees thermostat
Urd stage 3 clutch
650cc injectors
Urd fuel pump upgrade
Aluminum flywheel
Clutch master hydraulic throw out bearing
Urd stage 3 clutch
Djm front control arms lowers it 3”
2” lowering blocks in rear with qa1 shocks
Frame has djm c notch in rear
Urd traction bar powder coated black
Tundra front calipers powder coated
Isf factory rotors
Snow performance stage 3 meth injection kit. With tank in the bed
Very rare original trd spoiler on tail gate
Aem wide band, boost gauge, fuel pressure gauge
Nitto nt05 rear tires. 275/45r18
All tuned with hp tuners. Runs great. Probably missing other stuff.
I’m a Toyota master tech all work done by me.
No rust at all. Always garage kept in the winter.
Have 2 young kids now and don’t have time to enjoy. Have tons of money and time into the truck. I have over $7000 just into building the motor and $5000 in the supercharger. Looking for $25,000
2005 Toyota Tacoma xrunner
Bc rods
Cp ceramic coated pistons 9.5-1 compression
Arp head studs
All new Toyota bearings
Kelford custom cams with valve springs
New water pump
New timing chain with tensioner
Motor has less the 10k on rebuild
Tons of parts powder coated while motor was apart. No leaks nothing wrong with motor
Small port and polishing job on heads and intake along with super charger
76mm throttle body
Magnusson supercharger. Been on for around 15k
2.3” pulley making around 12 psi
Nst pulleys. Crank, supercharger lower, water pump, alternator
Super charger over flow tank in bed
Trd upgraded intake from 4 runner with new maf sensor
Doug thorley headers
Urd y pipe
Urd 3” cat back
Urd 170 degrees thermostat
Urd stage 3 clutch
650cc injectors
Urd fuel pump upgrade
Aluminum flywheel
Clutch master hydraulic throw out bearing
Urd stage 3 clutch
Djm front control arms lowers it 3”
2” lowering blocks in rear with qa1 shocks
Frame has djm c notch in rear
Urd traction bar powder coated black
Tundra front calipers powder coated
Isf factory rotors
Snow performance stage 3 meth injection kit. With tank in the bed
Very rare original trd spoiler on tail gate
Aem wide band, boost gauge, fuel pressure gauge
Nitto nt05 rear tires. 275/45r18
All tuned with hp tuners. Runs great. Probably missing other stuff.
I’m a Toyota master tech all work done by me.
No rust at all. Always garage kept in the winter.
Have 2 young kids now and don’t have time to enjoy. Have tons of money and time into the truck. I have over $7000 just into building the motor and $5000 in the supercharger. Looking for $25,000