Search results
-
-
URD Spec-U and Full Exhaust with Sound Clip
Yup, that V-band clamp is a beeotch haha.- rat7761
- Post #28
- Forum: N/A Mods & Tuning
-
URD Spec-U and Full Exhaust with Sound Clip
I used a deep socket with a universal joint and long extension on some and a ratcheting box wrench on others. On a few nuts near the air injection pipe, the box wrench wouldn't fit over the nut due to space. I needed to tighten those with the open end side.- rat7761
- Post #23
- Forum: N/A Mods & Tuning
-
URD Spec-U and Full Exhaust with Sound Clip
I wanna see what the instructions look like for the 2012+ Tacomas with air injection. Too late for me now but i'm sure there are tips that woulda saved me some time and headache.- rat7761
- Post #15
- Forum: N/A Mods & Tuning
-
URD Spec-U and Full Exhaust with Sound Clip
Not sure. Just buy a set. I found a cheap one on ebay that worked fine.- rat7761
- Post #14
- Forum: N/A Mods & Tuning
-
URD Spec-U and Full Exhaust with Sound Clip
Yup, took me 7 hours with air tools to install the headers and full exhaust with no instructions. I'm also an ASE certified technician. My hands and entire body are sore. I wouldn't wish this install on my worst enemy haha.- rat7761
- Post #9
- Forum: N/A Mods & Tuning
-
URD Spec-U and Full Exhaust with Sound Clip
Yeah it didn't come with instructions. I think there would have been a lot less swearing if there were instructions haha. Satisfied with the outcome but damn it was a lot of work...- rat7761
- Post #7
- Forum: N/A Mods & Tuning
-
URD Spec-U and Full Exhaust with Sound Clip
I'll stick to installing DTLTs on the 4x4s. I almost threw in the towel on this install. Most difficult header install I've ever done haha.- rat7761
- Post #3
- Forum: N/A Mods & Tuning
-
URD Spec-U and Full Exhaust with Sound Clip
Installed for a friend. 2013 4x4 TRD Sport Tacoma. Install was a pain! No instructions. Transmission crossmember needed to be removed to remove the stock Y-pipe. Steering shaft needed to be separated to install the driver's side header. You need to be careful not to turn the steering wheel...- rat7761
- Thread
- Replies: 31
- Forum: N/A Mods & Tuning
-
2016 Tacoma 4x4 DC/LB 1/4 Mile
I ran it in Drive. The sport shift is just a gear limiter. The truck shifts at 6,000 RPM in drive.- rat7761
- Post #4
- Forum: Sanctioned Events
-
2016 Tacoma 4x4 DC/LB 1/4 Mile
https://youtu.be/yt1ZqhmTgc4 https://youtu.be/GWo6H9h4CHU- rat7761
- Thread
- Replies: 3
- Forum: Sanctioned Events
-
-
-
Bypassing clutch accumulator
http://www.napaonline.com/Catalog/CatalogItemDetail.aspx/Brake-Line-Fitting-Metal-American-Grease-Stick-Company/_/R-BK_6415027_0361071590 -
URD Plug and Play O2 Simulator
https://youtu.be/QQ67YJZyxfQ- rat7761
- Thread
- Replies: 1
- Forum: N/A Mods & Tuning
-
Bypassing clutch accumulator
The accumulator mentioned here is in the clutch hydraulic system. I believe it restricts fluid flow to allow smoother engagement for novice drivers. When I took mine out I gained clutch travel for my dual friction clutch to allow it to fully disengage, the clutch became easier to depress and had... -
'05+ Tacoma Clutch Shuttle Valve Removal
Instructions for this mod came with my Competition Stage 3 Clutch but said it was only necessary for twin disc set ups. Clutch engagement feels better and now I can get it into 1st gear every time at a stop. Before I would have to put it in 3rd then 1st almost every time I pulled out.- rat7761
- Post #3
- Forum: F/I Mods & Tuning
-
'05+ Tacoma Clutch Shuttle Valve Removal
https://youtu.be/gNWWoNDpmDE The removal of the clutch shuttle valve (clutch accumulator) is required when installing a twin disc style clutch to gain more travel in the hydraulic system. I run a Competition Clutch Stage 3 dual friction clutch in my 2013 4x4 Tacoma and even with all the play...- rat7761
- Thread
- Replies: 21
- Forum: F/I Mods & Tuning
-
JB Weld 3RZ Block Repair
https://youtu.be/PsUYUZ3eqTM Repairing a pitted 3RZ block deck surface due to a blown head gasket with JB Weld.
