Search results
-
OEM oil cooler/ show me your oil sandwich plate
Anyone know what size the factory oil cooler hoses are. Inner diameter. Whose got the best aftermarket oil sandwich plate- Eraser
- Thread
- Replies: 0
- Forum: Stock Performance/Mechanical
-
low voltage mystery...
So, I keep getting p0137 and p0157 (both rear o2 sensors low voltage) every time I get on the freeway and cruise more than 5 minutes. I have an X1. I have short tubes and 2 catalytic converters with a completely custom exhaust. Suggestions? Can't pass emissions. update August 30th: Swapped...- Eraser
- Thread
- Replies: 4
- Forum: N/A Mods & Tuning
-
URD TCAI owners
Anyone have an issue with the MAF getting wet/damaged at a touchless car wash, I don't want to break stuff.- Eraser
- Thread
- Replies: 5
- Forum: N/A Mods & Tuning
-
Thought I should ask the pros
Trying to seal up 1/2" NPT holding fuel under 43.5psi. The NPT fittings have 3+ threads sealing, no threads bottoming out (99% sure) about 10 minutes after pressure/flow a gasoline leak springs... Have tried already: regular teflon pipe replacing NPT fittings gasoline resistant/-50F to...- Eraser
- Thread
- Replies: 4
- Forum: N/A Mods & Tuning
-
X1/107 fuel.... tune?
Anyone have a 107 octane fuel n/a tune for the X1? Planning on going to Southern International raceway on the 15th for test and tune if I get one.- Eraser
- Thread
- Replies: 9
- Forum: N/A Mods & Tuning
-
AEM 30-3002, Water/Methonal Injection System
Anyone have experience or opinions on using this kit with our naturally aspirated 1GRs?- Eraser
- Thread
- Replies: 19
- Forum: N/A Mods & Tuning
-
RR in Tucson
Saw the tail of a RR X headed north on Craycroft towards the gate on Davis Monthan.- Eraser
- Thread
- Replies: 1
- Forum: X-Runner Spotted
-
Emblem Idea
Saw attached photo in my parking lot at work this morning. Check it out.- Eraser
- Thread
- Replies: 9
- Forum: Exterior Modifications
-
Tremec 56
Would it be practical to do the swap on N/A. Or would it be overkill? Thoughts?- Eraser
- Thread
- Replies: 13
- Forum: N/A Mods & Tuning
-
XR radiant red, LRAFB
Spotted driving on the base with the tailgate down, looks like u just bought it, had the tags in the window. Saw u at 1130:- Eraser
- Thread
- Replies: 0
- Forum: X-Runner Spotted
-
Ultimate dog video
http://www.youtube.com/watch?v=nGeKSiCQkPw&feature=player_embedded Found this on www.break.com very funny- Eraser
- Thread
- Replies: 2
- Forum: Jokes & Humor
-
Fuel Rail
What is the type of material used for the stock fuel rail on the 1GR? Does anyone know of an aftermarket fuel rail made of aluminum for the 1GR?- Eraser
- Thread
- Replies: 6
- Forum: Stock Performance/Mechanical
-
AFE Stage 2 S.I. ...VS... URD TCAI
Which one is better? I will not be going the boosted route anymore, and was wondering if the URD TCAI would be worth the purchase in improvement over the AFE Stage 2 S.I. I currently have installed. Has anyone had both installed?- Eraser
- Thread
- Replies: 7
- Forum: N/A Mods & Tuning
-
Gearshifting, not so easy.
driving onto the freeway today when i shifted into third gear heard an awesome sounding clunk/bang from the transmission. no explosions or flying metal associated :dontknow: and then its significantly harder to engage into gears all the way home. when i came to a stop at my house i slowly...- Eraser
- Thread
- Replies: 10
- Forum: N/A Mods & Tuning
-
Melted?
I thought using "dead soft" aluminum as a collector gasket on my short tubes would seal any more leaks. after tightening and tightening I decided to just replace them. (see below for used aluminum gaskets) I replaced these in the photo with copper crush gaskets and have had no leaks for 2 weeks...- Eraser
- Thread
- Replies: 5
- Forum: N/A Mods & Tuning
-
XRU bretheren near Nellis AFB
Hey whoever is reading this, I'm bored @Nellis, anyone wanna hang out? (Send me a PM) -Zach- Eraser
- Thread
- Replies: 5
- Forum: General Off-Topic Discussions
-
X1 Noob...
Okay, was cruising home today on the freeway. got a CEL. I don't have a scangauge but I do have an X1, When i got home i pulled a data log. My question is can I pull the code with Xtune or search through the log to find the code that popped up earlier? Been searching through the forums and...- Eraser
- Thread
- Replies: 4
- Forum: Stock Performance/Mechanical
-
Apr x1 new hotness
Just got back from Vegas. my X1 is here. :rockon: I've been reading thru the instructions. I have the all the tools I need... except for a torque wrench. Anyone have any input as to where I could borrow/rent one for the job? All information is appreciated! ~ERASER- Eraser
- Thread
- Replies: 16
- Forum: N/A Mods & Tuning
-
Anyone in Vegas or surrounding area?
Hey folks, I'm here in Vegas on a business trip and was wondering if anyone wants to have a lil get together just to hang out and meet some fellow XRU members. PM me or reply if you 're interested. ~Zach- Eraser
- Thread
- Replies: 4
- Forum: General Off-Topic Discussions
-
remote start
Just a quick question if anyone has one or knows if it is possible on our trucks. lemme know.:hmmmm2: ~ERASER- Eraser
- Thread
- Replies: 7
- Forum: Interior Modifications
